Shanghai Sepna Chemical Technology Co.,Ltd
Call us on:+86-021-66310806      E-mail: sepna301@sepna.cc
    Products
    Abstract: If you are planning to wholesale best cheap and high quality transparent silicone gel for pcb board China, or hot sale transparent silicone gel for pcb board in China from professional silicone potting gel, soft silicone adhesive gel, silicone gel for electronics, thermally conductive gels, rtv silicone gel encapsulant manufacturers and suppliers and factory, please feel free to contact SEPNA, and welcome to check products price with us.
    Transparent Silicone Gel For PCB Board

    If you are planning to wholesale best cheap and high quality transparent silicone gel for pcb board China, or hot sale transparent silicone gel for pcb board in China from professional silicone potting gel, soft silicone adhesive gel, silicone gel for electronics, thermally conductive gels, rtv silicone gel encapsulant manufacturers and suppliers and factory, please feel free to contact SEPNA, and welcome to check products price with us.

    Transparent Silicone Gel For Electronics Potting SI2715

    ◆Detailed Product Description

    SI2715A/B is two component transparent self healing silicone gel, after cured it will be quite elastic material with buffer and self recovery. It’s used to isolate moisture and other noxious pollutant from contacting the circuit board, also used to dielectric of high voltage. The other usage is stress relief for protecting circuit and contact device from high temperature and mechanical stress.

    Features 

    1.1:1 addition type, good adhesive strength and self-healing

    2.Superior elasticity for stress relief

    3.Quite low oil penetration after cured, good anti-poisoning

    4.Good dielectric in high temperature, protect from high voltage

    5.Excellent age resistance and weather resistance

    6.Excellent waterproof, corrosion prevention, moisture proof and chemical media resistance

    Usage

    Use for semi conductor, connector, sensor potting and encapsulating.

    ◆Data Table

    Properties before curing

    Part

    2715A

    2715B

    Component

    polysiloxane

    Hydrogen polysiloxane

    Appearance

    Colorless liquid

    Colorless liquid

    Viscosity, mPa.s(25℃ )

    750

    600

    Density,  g/cm3(25℃ )

    0.99

    0.99

    Mixture/mass ratio

    A:B = 100:100

    Tensile strength after mixing,cps(25℃ )

    700

    Operation time after mixing, min(25℃ )

    40min

    Curing addition, min,25℃

    25℃ /5hours or 80℃ /30mins

    Properties after curing

    Appearance

    transparent gel

    Needle penetration,1/10mm

    70

    Dielectric strength, KV/mm

    25

    Volume resistance DC500V, Ω·cm

    1.1×1015

    Loss factor(1 MHz)

    <0.001

    Dielectric constant (1 MHz)

    2.8

    Application temperature, ℃

    - 60 ∽ 260

    Note:

    ①All data above were tested under standardized condition.

    ②All data listed in the chart were for the generalized item in the series; please refer to the related datasheet for special items.

    ③Storage condition has a direct impact to the products’shelf life, Please refer to the instruction for special items’storing.

    ◆Operation Attention

    1.Mix Part A and Part B by 1:1, pour directly into the protection needed component(or module).

    2.Still the potted component to let it discharge the bubble. It can cure in short time, about 30mins in 80℃. It also can be cured under room temperature, it needs about 4-5hours.

    ◆Notice

    1.Vacuum defoamation can provide the property of cured product

    2.The Mixed glue should be sealed after using

    3.Low temperature will slow the curing speed, advice to heat curing

    4.SI2715 will be hard to cure if contact with sulfur, amine or Sn

    ◆Package and Storage

    Package                                  Storage  

    Part A: 18KG Bucket               Shipped and stored as normal chemicals

    Part B: 18KG Bucket               Shelf life: 12 months(25℃)

    ◆Safety Operation Material

    MSDS isn't included here. Please read TDS, MSDS and label carefully before operation.You can get MSDS from Sepuna or other distributors, or mail to service center sepuna@sepuna.cn, or call +86-400-882-1323.

    ◆Product Warranty

    All product properties and application details based on information believe to be reliable and accurate. But you still need to test its property and safety before application. The advices we supply don't apply in any circumstances. Sepuna don't make assurance of any other applications outside the specification until Sepuna supply a special written guarantee. Sepuna is only responsible to replace or refund if this product is defective within the warranty period stated above. Sepuna makes it clear that will not be liable of any accidents.


    Hot Tags: transparent silicone gel for pcb board, silicone potting gel, soft silicone adhesive gel, silicone gel for electronics, thermally conductive gels, rtv silicone gel encapsulant, China, manufacturers, suppliers, factory, wholesale, cheap, high-quality, price, best, hot sale, in China

    Product Categories

    Fast Track

    Copyright © Shanghai Sepna Chemical Technology Co.,Ltd